0:00:07.812,0:00:11.145
Welcome to this "VMC Leveling" video

0:00:11.145,0:00:16.628
This VF-2SS is connected to air and power and is operational

0:00:16.628,0:00:19.912
however, the machine is not at the proper height or level

0:00:19.912,0:00:23.890
to provide optimal performance and accuracy

0:00:23.890,0:00:26.929
There are three steps to the leveling process

0:00:26.929,0:00:31.578
First, the machine is positioned at the correct height above the coolant tank

0:00:31.578,0:00:34.679
Second, level the machine front to back

0:00:34.679,0:00:38.844
and side to side to permit good coolant and chip flow

0:00:38.844,0:00:43.698
Finally, remove any Twist or Bow in the base casting

0:00:43.698,0:00:46.862
The tools needed for this procedure are:

0:00:46.862,0:00:51.028
a three quarter inch (3/4") socket and ratchet, a one and a half inch (1 ½") wrench

0:00:51.028,0:00:55.528
a tape measure, a 5 tenths or 1 micron test indicator

0:00:55.528,0:00:58.044
and a magnetic base to mount the indicator

0:00:58.044,0:01:01.545
and Haas Leveling Tool T-2181

0:01:01.545,0:01:06.994
A precision machinists level is also acceptable for taking level measurements

0:01:06.994,0:01:09.961
This video features a VF-2SS

0:01:09.961,0:01:14.346
but the same procedures apply to all VF Series machines

0:01:14.346,0:01:18.145
Larger machines with outrigger supports require additional steps

0:01:18.145,0:01:20.112
during the leveling process

0:01:20.112,0:01:22.078
This information can be found in the Haas

0:01:22.078,0:01:24.202
machine Installation manual

0:01:24.202,0:01:26.327
To clear the coolant tank

0:01:26.327,0:01:30.127
lift the Base Casting three and a half (3 ½") inches off the ground

0:01:30.127,0:01:36.095
by adjusting the four corner leveling screws to the same height

0:01:36.095,0:01:37.419
On base castings with

0:01:37.419,0:01:41.478
6 or 8 leveling screws the middle screws should not be touching

0:01:41.478,0:01:45.227
the pads during the leveling procedure

0:01:45.227,0:01:50.076
Move the X and Y axes until the table is centered

0:01:50.076,0:01:54.362
Clean the table surface and the leveling tool

0:01:54.362,0:01:58.293
Make sure the calibration of your level is correct before starting

0:01:58.293,0:02:01.763
Place tool T-2181 on the mill table

0:02:01.763,0:02:06.412
and monitor the exact position of the bubble on the precision vial

0:02:06.412,0:02:08.528
Using a t-slot for alignment

0:02:08.528,0:02:14.845
rotate the level 180 degrees and place it in the same position on the table

0:02:14.845,0:02:18.111
The bubble should stay in the exact same position

0:02:18.111,0:02:21.097
If the values are different by more than one division

0:02:21.097,0:02:25.263
then the level should be returned to Haas for adjustment

0:02:25.263,0:02:27.695
With the leveling tool at the center of the table

0:02:27.695,0:02:33.061
and the short leveling vial parallel to the Y-axis, the shorter vial is measuring the angle

0:02:33.061,0:02:36.928
of the machine front to back

0:02:36.928,0:02:41.211
Lift either the front or back of the base casting as necessary

0:02:41.211,0:02:43.112
to make the machine level

0:02:43.112,0:02:45.013
Remember to always lift the

0:02:45.013,0:02:49.128
lower end of the machine to maintain clearance to the coolant tank

0:02:49.128,0:02:52.546
Each time you make an adjustment turn both leveling screws

0:02:52.546,0:02:55.711
on that end an equal amount

0:02:55.711,0:02:58.943
Adjust the screws until the bubble is centered

0:02:58.943,0:03:04.911
Adjustments close to zero will make subsequent changes easier

0:03:04.911,0:03:09.412
With the machine leveled front to back, use the longer precision level

0:03:09.412,0:03:12.499
lying along the X-axis, which shows the angle

0:03:12.499,0:03:16.478
of the machine from left to right

0:03:16.478,0:03:20.429
Again, lift the lowest side of the machine to bring it level

0:03:20.429,0:03:23.714
and turn both screws an equal amount

0:03:26.330,0:03:28.191
With the machine now level

0:03:28.191,0:03:30.716
front to back and side to side

0:03:30.716,0:03:36.245
continue using the longer vial parallel to the X-axis

0:03:36.245,0:03:39.962
We are now ready to check for twist in the base casting

0:03:39.962,0:03:43.478
Start with the mill table at the front of the machine

0:03:43.478,0:03:46.174
look at the position of the indicating bubble

0:03:46.174,0:03:51.251
Move the Y-axis across its full travel stopping at the column

0:03:51.251,0:03:55.077
At the column side, look to see which rear corner of the machine

0:03:55.077,0:03:59.429
if any, is lowest as shown by the leveling tool

0:03:59.429,0:04:02.395
In this video, the leveling tool is angled down

0:04:02.395,0:04:08.047
at the right rear corner of the machine as we get to full axis travel at the column

0:04:08.047,0:04:11.578
This shows the right rear corner of the machine is low

0:04:11.578,0:04:15.728
The value is three marks away from zero

0:04:15.728,0:04:18.347
Lift the right rear corner of the machine

0:04:18.347,0:04:23.228
until the leveling tool reads zero

0:04:23.228,0:04:25.980
Now move the table to the front of the machine

0:04:25.980,0:04:28.789
and note which side is lowest

0:04:28.789,0:04:34.044
Adjust the lowest corner up until the leveling tool reads zero

0:04:34.044,0:04:38.628
Move the table across travel and each time adjust the leveling tool value

0:04:38.628,0:04:43.712
to zero by lifting the low corner of the machine

0:04:43.712,0:04:46.277
Usually the value will change several times

0:04:46.277,0:04:49.439
and get nearer to zero with each adjustment

0:04:49.439,0:04:56.612
Repeat this step until the bubble is adjusted to zero at both ends of the Y-axis travel

0:04:56.612,0:05:01.495
Next, adjust the middle leveling screws until lowered onto the leveling pucks

0:05:01.495,0:05:06.603
Hand-tighten each screw onto the puck until the puck stops turning

0:05:06.603,0:05:11.837
Set each screw by tightening an additional 10 degrees

0:05:11.837,0:05:13.911
With the middle screws tight the remaining

0:05:13.911,0:05:18.096
steps in this process are: Re-measuring for Twist

0:05:18.096,0:05:20.753
and measuring for Bow in the base casting

0:05:20.753,0:05:23.259
and then measuring the Spindle Sweep.

0:05:23.259,0:05:28.862
Any adjustments from this point forward will be done with the middle screws ONLY

0:05:28.862,0:05:32.430
with both middle screws adjusted the same each time[br]

0:05:32.430,0:05:36.510
These adjustments should be very small as we are almost finished

0:05:36.510,0:05:42.144
With the leveling tool still parallel to the X-axis, re-measure for twist

0:05:42.144,0:05:44.493
Start at the operator side

0:05:44.493,0:05:48.163
move to the middle of Y-axis travel

0:05:48.163,0:05:51.895
and then to the Column side

0:05:51.895,0:05:57.444
Adjust the middle screws to remove any twist caused when the screws were tightened

0:05:57.444,0:05:59.980
Again, ONLY very small adjustments

0:05:59.980,0:06:07.430
should be made to the middle screws while re-measuring the level values

0:06:07.430,0:06:11.429
Next, measure for any bow, either up or down

0:06:11.429,0:06:13.652
along the length of the Base Casting

0:06:13.652,0:06:16.947
Place the Leveling Tool in the center of the Mill Table

0:06:16.947,0:06:21.826
with the precision vial parallel to the Y-axis

0:06:21.826,0:06:25.328
Look at the bubble position at the operator side

0:06:25.328,0:06:28.729
at the middle of Y-axis travel

0:06:28.729,0:06:31.545
and at the Column side

0:06:31.545,0:06:36.677
If the measurement shows there is bow in the base casting in either the up or down direction

0:06:36.677,0:06:41.561
use the middle screws to make adjustments

0:06:41.561,0:06:43.976
Remember, only move the screws

0:06:43.976,0:06:47.244
in small and equal amounts

0:06:47.244,0:06:49.944
The tolerance for both the twist and bow measurements is

0:06:49.944,0:06:57.477
0.0002" over 10" or 0.02mm over a meter

0:06:57.477,0:06:59.811
Errors because of twist or bow will cause

0:06:59.811,0:07:02.624
errors in the spindle tram values

0:07:02.624,0:07:08.845
With the twist and bow adjustments complete carefully remove the leveling tool

0:07:08.845,0:07:12.945
Attach the Test Indicator to the Magnetic Base

0:07:12.945,0:07:17.370
Move the spindle head down to the middle of Z-axis travel

0:07:17.370,0:07:21.397
Attach the magnetic base to the spindle

0:07:21.397,0:07:27.958
Position the test indicator to measure a 10" or 250mm diameter circle

0:07:27.958,0:07:31.429
Move the table to a position where the test Indicator tip

0:07:31.429,0:07:34.278
will remain on the table's surface when facing both the

0:07:34.278,0:07:37.262
front and column sides of the machine

0:07:37.262,0:07:42.976
Moving the Z-axis in "tenths" mode, bring the Test Indicator down to contact the

0:07:42.976,0:07:46.328
mill table and zero the test indicator

0:07:46.328,0:07:49.818
Take a measurement every 90 degrees of rotation

0:07:49.818,0:07:53.354
This provides two values along the Y-axis

0:07:53.354,0:07:56.136
and along the X-axis

0:07:56.136,0:07:58.795
Total Indicator Reading for all four positions

0:07:58.795,0:08:05.161
should not exceed 0.0005 inches or 0.013 mm

0:08:05.161,0:08:06.979
If the spindle sweep is not within

0:08:06.979,0:08:10.494
specification along the Y-axis, we can use the

0:08:10.494,0:08:14.299
middle screws to make very small adjustments to the sweep readings

0:08:14.299,0:08:18.491
while changing the bow and twist values by a negligible amount

0:08:18.491,0:08:22.007
Each time you make a middle screw adjustment to change spindle sweep

0:08:22.007,0:08:25.653
be sure to re-zero your test indicator at the operator side

0:08:25.653,0:08:28.839
before re-measuring the effect of your adjustment

0:08:28.839,0:08:32.610
This will minimize the chance of confusing values

0:08:32.610,0:08:35.041
In this video the test indicator starts

0:08:35.041,0:08:38.140
with a value of 0 facing the front of the machine

0:08:38.140,0:08:41.670
We see 0.0001 at the right hand quadrant

0:08:41.670,0:08:44.682
-0.0002 at the back side of the table

0:08:44.682,0:08:48.920
and 0.0002 at the left hand quadrant

0:08:51.351,0:08:54.789
If the value at the back had been out more than 0.0005

0:08:54.789,0:08:56.328
a very small adjustment

0:08:56.328,0:08:58.031
to the middle leveling screws

0:08:58.031,0:09:01.395
to either lift or drop the table would be required

0:09:01.395,0:09:05.112
Only the values from front to back can be effectively changed

0:09:05.112,0:09:09.354
by adjustment of the middle leveling screws

0:09:09.354,0:09:13.012
If the adjustments to make spindle sweep better are very small

0:09:13.012,0:09:15.978
you don't need to check bow and twist again

0:09:15.978,0:09:18.395
Lock the leveling screws in place

0:09:18.395,0:09:24.447
Tighten the locking nuts while holding the leveling screws so they don’t rotate

0:09:24.447,0:09:27.145
The customer's machine is now at the proper height

0:09:27.145,0:09:31.077
and level and is free of any twist or bow in the base casting

0:09:31.077,0:09:35.806
This provides the basis for optimal machine accuracy