0:00:00.061,0:00:01.311 Welcome again 0:00:01.598,0:00:06.070 Today I'll be showing you another video[br]about designing in SketchUp 0:00:06.363,0:00:11.634 We'll be creating a plan for an item[br]that I already made in the workshop 0:00:12.048,0:00:18.312 a children's cabinet with drawers 0:00:18.525,0:00:19.793 Let's begin! 0:00:27.726,0:00:31.709 We'll jump straight into SketchUp[br]and begin working 0:00:31.744,0:00:41.104 Where would I start? With establishing our[br]working area or the exterior dimensions 0:00:43.534,0:00:51.914 The cabinet is 570mm wide and 460mm deep 0:00:54.148,0:00:58.968 The height is 515mm 0:01:00.458,0:01:04.518 whoops, not 215… 515mm 0:01:05.038,0:01:08.139 These are the exterior dimensions 0:01:08.229,0:01:10.219 I'll erase the center, I don't need it 0:01:11.405,0:01:16.437 Create some guide lines on the bottom 0:01:17.295,0:01:19.778 And we'll start working on the upper part 0:01:20.114,0:01:25.451 A very simple top,[br]I only need to round the corners 0:01:26.481,0:01:31.139 I'll make it this way:[br]create guide lines at 20mm 0:01:34.149,0:01:37.017 Press A for arc 0:01:40.923,0:01:45.033 After we have the first arc[br]double-click the rest of the corners 0:01:47.483,0:01:49.925 Pull to 24mm 0:01:51.323,0:01:53.374 Erase redundant lines 0:01:54.300,0:02:01.394 Select the whole part and create component[br]we'll just name it "top" 0:02:03.190,0:02:04.476 and that's it 0:02:05.695,0:02:07.682 Now we can work on the legs 0:02:09.566,0:02:13.934 I'll erase this whole part[br]and we can begin drawing 0:02:15.471,0:02:19.266 The leg is 45mm wide… 0:02:21.256,0:02:23.561 I'll check again… 0:02:24.031,0:02:29.429 45 x 460 mm[br] 0:02:29.909,0:02:34.967 and is also 24mm high 0:02:40.137,0:02:47.581 The front round over was,[br]I think, about 15mm 0:02:49.235,0:02:52.427 Maybe even less, maybe 10mm 0:02:55.869,0:02:58.143 Again, create an arc[br] 0:02:59.633,0:03:00.727 Done 0:03:01.589,0:03:03.953 The same on the other side 0:03:04.443,0:03:14.130 Now push these parts 0:03:21.944,0:03:23.325 Boom, done 0:03:24.288,0:03:28.651 Create component – "foot" 0:03:32.020,0:03:35.178 So this part is done. What now? 0:03:35.598,0:03:38.244 Now maybe let's make the side panel 0:03:38.244,0:03:44.871 But first I need to create[br]some guide lines under tho top 0:03:46.326,0:03:50.212 15mm from the front 0:03:51.716,0:03:54.090 10mm from the side 0:03:55.024,0:03:56.828 10mm from the back… 0:03:57.850,0:04:01.883 and the other side 10mm as well 0:04:06.762,0:04:10.058 OK, press R 0:04:10.918,0:04:14.204 and draw another rectangle 0:04:14.644,0:04:19.633 The side panel was 20mm thick by 435mm 0:04:21.143,0:04:23.002 435 0:04:24.622,0:04:29.611 I can pull that to the foot 0:04:37.079,0:04:43.942 Group it into a component[br]Let's name it "side1" 0:04:44.414,0:04:50.000 Might as well create the housing[br]right away 0:04:52.202,0:04:56.988 Ctrl-H to hide all others,[br]you should already know this 0:04:57.753,0:05:02.235 And we'll draw the housing[br]for the back panel 0:05:03.014,0:05:08.074 The housing is 15mm by 4mm 0:05:14.576,0:05:20.015 Push it all the way up 0:05:23.783,0:05:24.869 That's it 0:05:25.910,0:05:28.420 The side panel is done 0:05:29.792,0:05:36.724 The foot was moved back, I think I talked[br]about it in the end of the other video 0:05:36.862,0:05:40.962 So that it is flush with the side panel 0:05:42.163,0:05:49.052 Now we can move both these parts 0:05:54.951,0:05:57.313 and copy them to the other side 0:06:11.267,0:06:16.511 Move this part and rotate it 0:06:20.031,0:06:21.884 so that it's mirrored 0:06:23.937,0:06:32.899 Now it's only a matter of moving the foot 0:06:34.099,0:06:35.731 This way 0:06:39.281,0:06:42.953 Pressing Shift, as you remember, locks the[br]movement axis 0:06:42.953,0:06:48.083 And we just move it to this point 0:06:54.089,0:06:59.119 Now we need to make to bottom part 0:06:59.158,0:07:05.150 But first I need to recede the side panels 0:07:05.230,0:07:09.062 to later accomodate the drawer fronts 0:07:09.152,0:07:14.596 The drawer fronts were also 24mm thick,[br]so push it back 0:07:18.518,0:07:23.768 Now we're left with drawing[br]the cabinet floor 0:07:26.472,0:07:30.472 I'm looking for the proper point to start 0:07:33.445,0:07:37.445 OK, draw it from here 0:07:38.649,0:07:43.139 The floor was a little bit thinner[br]– 16mm 0:07:44.036,0:07:50.780 We'll also pull it this way…[br]or maybe we can just draw it like this 0:07:53.180,0:07:54.814 on the bottom 0:07:58.794,0:08:06.519 510mm x 4mm 0:08:07.065,0:08:13.488 510 by 4… 0:08:15.838,0:08:24.631 and pull it 4mm, done 0:08:25.231,0:08:30.544 Make component – "floor", done 0:08:32.131,0:08:36.131 Virtually the whole[br]cabinet body is finished 0:08:37.372,0:08:42.492 I won't be making the back panel just yet,[br]it's not necessary at this stage 0:08:43.653,0:08:47.293 We can now remove the old guide lines 0:08:47.435,0:08:49.735 so they won't distract us 0:08:50.941,0:08:57.251 The ones on the bottom as well 0:08:58.233,0:09:00.793 Let's save the progress 0:09:06.597,0:09:11.087 It's time to set the dimensions 0:09:11.563,0:09:14.023 for the drawer fronts 0:09:14.448,0:09:19.348 The fronts will determine the whole[br]inside grid 0:09:21.650,0:09:24.880 This will be unfortunately[br]a little bit more challenging 0:09:29.643,0:09:31.293 2mm from the top 0:09:33.510,0:09:39.470 And also 2mm from the bottom 0:09:39.962,0:09:41.562 That's at least what I did 0:09:43.075,0:09:49.615 Let's now measure[br]how much space we got left 0:09:53.550,0:09:57.310 400… I'll need to write it down… 0:09:57.546,0:10:05.282 462mm minus 6mm that will be needed for 0:10:05.282,0:10:11.058 the gaps between the drawer fronts 0:10:12.718,0:10:20.166 So, 462 minus 6 equals 456 0:10:21.114,0:10:23.642 divide it by 4 0:10:23.882,0:10:28.322 equals 114 – that's our front height 0:10:31.388,0:10:34.380 Now for the second dimension 0:10:38.788,0:10:43.395 Also 2mm… 0:10:46.905,0:10:49.952 from both sides 0:11:08.712,0:11:14.801 I wonder where that decimal came from…[br]But it's 546mm 0:11:16.420,0:11:22.340 546 minus 2… 0:11:36.245,0:11:43.825 546 minus 2, divided by 2… 0:11:43.842,0:11:46.302 272 0:11:46.497,0:11:54.507 So now we have the full dimensions of our[br]future drawer fronts 0:11:57.712,0:12:01.872 I can now draft the front 0:12:06.633,0:12:14.913 272mm by 114mm 0:12:18.582,0:12:28.622 Pull to 24mm thickness 0:12:29.903,0:12:36.163 Make component – "front1"[br] 0:12:39.611,0:12:41.651 Should match 0:12:44.216,0:12:48.836 We can move it right away[br]to the correct position 0:12:58.850,0:13:01.240 Now the moment of truth… 0:13:03.458,0:13:05.473 If I place it here… 0:13:13.573,0:13:16.468 and divide by 3… 0:13:16.978,0:13:20.834 Everything should fit[br]and it does 0:13:21.890,0:13:25.734 Now we have to make the notches 0:13:26.154,0:13:27.878 for drawer handles 0:13:29.728,0:13:32.014 Let's edit the component 0:13:37.338,0:13:41.628 First mark the center 0:13:44.184,0:13:51.734 Now, if I remember correctly,[br]it was 20mm from the top 0:13:53.374,0:14:02.694 The notch was 100mm wide, so the lines are[br]50mm from the center each 0:14:03.630,0:14:10.903 The radius was about 10mm 0:14:11.103,0:14:17.916 So, one more and we can start drawing 0:14:38.346,0:14:42.091 I created two more guide lines 0:14:59.484,0:15:06.124 I need to draw some straight lines first[br]so the arc has something to attach to 0:15:07.600,0:15:11.740 Like this… 0:15:14.908,0:15:22.917 Now we only need to delete this part 0:15:25.327,0:15:28.636 And the fronts are done 0:15:29.386,0:15:34.326 Of course I can now erase the guide lines[br]Won't be needing them anymore 0:15:43.073,0:15:48.193 Ctrl-S, remember to save your work 0:15:50.400,0:15:58.500 Now I just have to merge the two bottom[br]drawers into one 0:15:58.500,0:16:00.130 We'll do it this way: 0:16:03.152,0:16:04.576 Select… 0:16:07.456,0:16:09.686 Wait, is this correct? 0:16:11.506,0:16:12.326 This is… 0:16:13.066,0:16:17.026 OK, I need to also make this one unique 0:16:21.767,0:16:22.667 Like this 0:16:24.275,0:16:31.525 Now we open the component and copy it[br]with Ctrl-C 0:16:34.197,0:16:37.337 Delete it, edit the other drawer 0:16:38.255,0:16:42.255 And paste it in here 0:16:42.632,0:16:48.872 So now both objects belong to[br]one component 0:16:50.286,0:16:57.757 Now we just need to close the gaps 0:17:07.997,0:17:09.738 It already closed itself 0:17:10.148,0:17:16.441 Select the eraser tool[br]and we can erase these lines 0:17:23.458,0:17:27.668 Deselect, close the component 0:17:27.927,0:17:34.757 We have a finished "front_bottom" 0:17:39.593,0:17:47.343 Now for the system of drawer slides[br]we have to go inside 0:17:47.393,0:17:50.923 and begin work on this part 0:17:52.258,0:17:53.728 Where would I start? 0:17:56.985,0:18:04.505 The slides will, of course, be a little[br]higher than the bottom of the drawer 0:18:05.268,0:18:21.738 So we have to add a couple of millimetres [br]to where the bottom of the drawer will be 0:18:24.423,0:18:29.853 Whoops, where am I?[br]Zoomed out too much 0:18:30.002,0:18:35.622 So that was 102mm, let's continue 0:18:40.025,0:18:41.395 116mm… 0:18:54.024,0:18:58.264 Again 116mm here 0:19:02.204,0:19:03.644 That's correct 0:19:03.684,0:19:13.894 So the first slide will be,[br]let's say, 5mm higher 0:19:19.970,0:19:21.064 5… 0:19:24.904,0:19:25.884 5… 0:19:28.334,0:19:29.244 5… 0:19:34.714,0:19:40.870 As you remember, I tried to make all the[br]slides from the same material 0:19:40.870,0:19:49.970 It was 30mm wide and 16mm thick 0:19:52.231,0:19:53.951 Thats the piece 0:19:57.819,0:20:02.259 We can pull it to the other side 0:20:07.309,0:20:10.709 Make component – "slide1" 0:20:13.542,0:20:19.492 We can also copy it to the back 0:20:22.222,0:20:29.522 The next slide that was definitely there,[br]as you can remember, or not… 0:20:31.901,0:20:33.721 was on the side 0:20:36.759,0:20:43.449 30mm, make component – "slide2" 0:20:48.295,0:20:52.295 I can already move this one 0:20:59.083,0:21:01.383 Grab it by the bottom 0:21:04.155,0:21:05.975 Move it up a level 0:21:06.998,0:21:08.598 and two levels up 0:21:10.594,0:21:16.544 Also, we can move all three of them 0:21:21.044,0:21:25.044 to the other side of the cabinet 0:21:29.488,0:21:30.538 That's good 0:21:31.717,0:21:33.657 What's left is… 0:21:34.861,0:21:37.871 adding the vertical slides 0:21:51.570,0:21:56.710 255mm, that's the center 0:22:01.264,0:22:08.362 8mm this way… 0:22:13.852,0:22:15.320 …and 8 the other way 0:22:20.910,0:22:24.970 Draw another rectangle[br]This will be our next part 0:22:25.081,0:22:26.711 This time a vertical one 0:22:29.869,0:22:33.569 Pull it all the way to the top[br]of the cabinet 0:22:34.171,0:22:36.241 Group component 0:22:36.514,0:22:39.834 This will be "slide3" 0:22:41.322,0:22:44.082 We can also copy it to the back now 0:22:54.122,0:23:02.492 We don't need these side guide lines[br]anymore. Erase them 0:23:06.944,0:23:07.814 Okay… 0:23:09.643,0:23:13.463 Now we have to make the[br]center slides, right? 0:23:14.604,0:23:15.534 So… 0:23:21.052,0:23:22.832 From the bottom 0:23:35.066,0:23:39.396 We need to set up some more guide lines 0:24:32.912,0:24:34.542 Let's continue drawing 0:24:37.624,0:24:41.864 16mm by 30mm 0:24:45.367,0:24:46.557 Pull it… 0:24:55.952,0:24:57.552 …to here 0:24:59.197,0:25:02.397 Make component – "slide4" 0:25:14.565,0:25:17.355 I see an error here 0:25:18.117,0:25:22.877 This must go 16mm higher 0:25:24.933,0:25:31.533 Because there was[br]a horizontal element here 0:25:33.902,0:25:35.812 OK, let's do it like this 0:25:37.012,0:25:38.462 This way 0:25:40.596,0:25:46.636 Pull it 50mm (correction: should be 30mm)[br]this way 0:25:48.366,0:25:51.406 and 50mm (again, should be 30mm) this way 0:25:53.056,0:26:00.236 Make component – "slide…" 5 or 6?[br]OK, let's make it 6 0:26:00.257,0:26:06.807 Now we can move these two parts togheter 0:26:10.833,0:26:13.733 116mm down 0:26:15.460,0:26:16.890 That's correct 0:26:20.658,0:26:24.198 And once again 116mm down 0:26:25.857,0:26:28.877 OK, as you can see there's a lot going on 0:26:30.896,0:26:34.896 I can erase all the guide lines 0:26:37.000,0:26:40.780 Won't be needing them anymore 0:26:43.084,0:26:45.754 This and this as well 0:26:48.651,0:26:50.841 Now the object is clean 0:26:52.583,0:26:54.573 Ctrl-S to save 0:26:56.111,0:26:58.421 Why don't we make the back panel now? 0:26:58.421,0:26:59.131 Easy 0:27:01.920,0:27:02.780 Press R 0:27:11.953,0:27:17.343 Drag it to here 0:27:19.357,0:27:21.017 4mm 0:27:21.702,0:27:25.702 Select, make component – "back_panel" 0:27:30.411,0:27:32.501 Are we missing anything? 0:27:33.030,0:27:37.030 Well, the drawers themselves, of course 0:27:37.030,0:27:39.150 So, the whole box 0:27:39.447,0:27:42.380 OK, while we're at it[br]we'll make the boxes as well 0:27:43.133,0:27:46.826 I can hide the top for now,[br]I don't need it 0:27:48.962,0:27:51.042 And let's make a drawer 0:27:56.313,0:27:57.383 Drawer… 0:28:02.617,0:28:11.437 As you can remember, I made some[br]additional notches in the front of the box 0:28:11.437,0:28:16.627 because I wanted the box to be[br]as high as posiible 0:28:17.399,0:28:21.789 It was, of course, a bit tedious 0:28:21.789,0:28:27.529 I wouldn't do that again the same way 0:28:28.947,0:28:32.947 So I'll skip the notches here 0:28:38.692,0:28:41.422 We'll do it like this for now 0:29:11.325,0:29:12.325 5mm 0:29:15.046,0:29:18.836 5mm from the end should be enough as well 0:29:19.825,0:29:23.505 We can now draw the side of the box 0:29:29.653,0:29:35.583 Pull it to 10mm thickness 0:29:35.749,0:29:42.669 Make component, we'll name it "box_side" 0:29:46.284,0:29:48.234 Move it to the other side 0:30:00.292,0:30:06.232 Now the back part 0:30:09.324,0:30:10.684 Also 10mm 0:30:12.843,0:30:20.783 Component "box_back" 0:30:26.240,0:30:31.840 Duplicate and move it 0:30:33.726,0:30:42.436 I won't be making this part[br]unique just yet 0:30:42.838,0:30:46.308 Let's hide the back panel as well 0:30:46.577,0:30:50.577 Now I'll make the housing dados for[br]the drawer floor 0:30:52.018,0:30:53.588 Open the side 0:30:57.629,0:31:00.859 5mm should be fine 0:31:02.673,0:31:05.543 5mm from the bottom 0:31:07.143,0:31:09.313 Make the housing 0:31:11.844,0:31:16.984 The drawer floor is 3mm thick[br]so 3mm by 5mm 0:31:18.235,0:31:24.355 Now push it all the way 0:31:35.151,0:31:40.641 Rotate this element this way 0:31:41.939,0:31:49.549 Now for the front and back housing 0:31:50.579,0:31:52.649 5mm here 0:31:53.711,0:31:55.241 5mm here 0:32:02.651,0:32:05.281 5 by 3 millimeters 0:32:05.762,0:32:06.932 Push 0:32:10.937,0:32:12.377 Almost ready 0:32:13.465,0:32:14.689 Rotate this part… 0:32:18.539,0:32:22.263 …around the blue axis 0:32:24.943,0:32:27.549 Whoops, not blue but green, sorry 0:32:31.148,0:32:31.688 Yep 0:32:33.422,0:32:39.462 So, what now? We need to make the[br]middle part of the drawer 0:32:39.944,0:32:42.894 I mean the floor, sorry 0:32:45.200,0:32:47.190 We'll do it like this 0:32:47.190,0:32:53.230 I'll draw a rectangle here 0:32:55.790,0:32:57.350 Offset it by… 0:32:58.552,0:33:03.962 the housing is 5mm[br]so 4.5mm 0:33:10.480,0:33:12.710 And now… 0:33:35.694,0:33:38.254 I'm just erasing the redundant lines 0:33:45.480,0:33:52.110 I can now pull the whole thing[br]to 3mm thickness 0:33:53.312,0:34:04.382 And that's our "small drawer floor" 0:34:08.420,0:34:11.090 Enable X-ray mode 0:34:13.272,0:34:19.092 And move it down into the housing 0:34:39.758,0:34:41.788 OK, it's in place 0:34:55.279,0:34:56.519 All is right 0:34:59.741,0:35:02.381 Just check again, X-ray 0:35:07.485,0:35:11.485 That's it, everything correct 0:35:13.319,0:35:16.689 Again, erase the guide lines 0:35:18.209,0:35:21.439 Keep the project clean 0:35:46.636,0:35:52.316 All right, everything cleaned 0:35:52.316,0:35:56.316 And the whole drawer is finished[br]so now it's only a matter of 0:35:58.933,0:36:01.343 grouping this all together 0:36:01.345,0:36:04.845 so 1, 2, 3, 4 0:36:06.252,0:36:08.592 and… the middle 0:36:11.298,0:36:17.718 Make component – "drawer1" 0:36:25.901,0:36:29.901 Got one more guide line left somewhere 0:36:31.950,0:36:32.890 Here 0:36:43.003,0:36:44.733 Now it's OK 0:36:45.993,0:36:47.973 Now I can finally copy it 0:36:56.910,0:36:59.680 Does it fit? It has to 0:37:08.464,0:37:10.234 Copy it down 0:37:14.448,0:37:16.148 And again 0:37:24.313,0:37:33.203 Now we only have to remake this[br]into the bottom drawer 0:37:33.203,0:37:34.983 which is the widest 0:37:42.877,0:37:47.567 We can also group these objects right away 0:37:49.295,0:37:50.235 Group 0:37:52.007,0:37:56.157 G is the keyboard shortcut 0:37:57.230,0:38:00.440 Grouped, grouped, grouped… 0:38:02.730,0:38:06.560 …grouped and grouped 0:38:07.065,0:38:10.445 Now it's only the bottom drawer left,[br]as I said 0:38:11.792,0:38:14.592 We'll make these two unique 0:38:17.423,0:38:21.023 And now we need to destroy this 0:38:24.454,0:38:29.624 So we'll make this unique as well,[br]because we'll be merging them 0:38:31.338,0:38:34.618 Delete this side in this one 0:38:36.957,0:38:40.937 and this side in that one 0:38:52.905,0:38:53.965 Ctrl-H 0:38:57.806,0:38:59.606 Extend… 0:39:04.128,0:39:07.758 And again, these pieces are unfortunately[br]nested 0:39:09.555,0:39:13.105 So we'll need to make this one unique[br]as well 0:39:24.413,0:39:25.323 Good… 0:39:38.207,0:39:40.637 This one unique as well 0:39:44.793,0:39:50.323 And we'll just extend this side 0:40:02.779,0:40:04.249 Delete this 0:40:05.662,0:40:14.022 Now we only have to remake[br]the drawer floor 0:40:17.673,0:40:21.673 I'll hide these elements because[br]I can't see down there 0:40:49.777,0:40:52.007 OK, the drawer floor 0:40:56.683,0:40:58.803 Make this unique 0:41:11.853,0:41:13.983 And extend it… 0:41:24.326,0:41:25.706 all the way to here 0:41:27.798,0:41:29.298 Deselect 0:41:31.158,0:41:32.628 I can delete this 0:41:44.369,0:41:46.707 The floor is done, but there's still[br]a seam in the middle 0:41:50.987,0:41:52.295 We need to… 0:41:58.915,0:42:00.403 That's better 0:42:02.224,0:42:05.244 That's how it should look 0:42:08.242,0:42:12.462 Select all, unhide 0:42:13.957,0:42:17.957 So, our cabinet is ready, right? 0:42:18.775,0:42:25.495 Now only the last group 0:42:28.410,0:42:30.800 This whole drawer 0:42:35.514,0:42:37.434 and the front panel 0:42:39.092,0:42:42.032 Letter G to group 0:42:46.538,0:42:48.078 Show the back panel 0:42:52.321,0:42:54.931 Rotate, and let's see if it works 0:42:56.928,0:42:58.328 The bottom drawer 0:43:00.825,0:43:03.195 Works?[br]Works 0:43:07.881,0:43:15.811 As you can see all the drawers work fine 0:43:22.786,0:43:23.686 And that's it! 0:43:23.899,0:43:27.899 I made a pretty long video from a short[br]instruction 0:43:27.899,0:43:31.899 but I think some folks might[br]find it useful 0:43:31.904,0:43:39.924 I virtually made the whole cabinet in this[br]design, every single part of it 0:43:39.924,0:43:46.724 You can now pick it apart, piece by piece 0:43:47.524,0:43:50.957 Break it up into parts 0:43:50.957,0:43:53.820 Grab the pieces 0:43:53.820,0:43:59.127 Move them and make an exploded view 0:44:01.317,0:44:05.154 Explode it, dismantle it 0:44:05.154,0:44:09.742 So you can better see how it's made 0:44:11.767,0:44:17.557 It's a very useful form of presentation 0:44:35.337,0:44:42.102 You can prepare it like this to show[br]the piece of furniture to someone 0:44:44.362,0:44:47.957 Have it broken up into parts 0:44:47.957,0:44:51.012 That's a form of presentation I recommend 0:44:51.856,0:44:59.976 It's also easier to see the number[br]of parts, in this case in a cabinet 0:45:00.918,0:45:03.538 You can see there's quite a lot[br]of elements 0:45:14.684,0:45:16.454 A little bit more to the front 0:45:27.837,0:45:32.707 That's how I would leave it,[br]don't overcomplicate it 0:45:34.070,0:45:37.530 That's it for today[br]Thank you for watching 0:45:38.185,0:45:44.075 Stay tuned for upcoming videos about[br]SketchUp and more 0:45:44.236,0:45:46.486 See you next time!